How to reset the router
- Press and hold the Router reset button for at least 20 t0 30 seconds.
- When the time completes, you will notice some changes in the light of the router, which means that your router has reset.
- Now, wait until router reboots.
Do you own a bitmain router? And don’t know how to login to the admin console and make necessary changes to it? If you’re having trouble accessing the bitmain router, then you’re in the right place.
Today, I’m going to share the steps through which you can easily log in to your bitmain router and make the changes you want easily, but the first thing we need to know before accessing the admin panel of bitmain router is its default IP address.
Most of the time, the default IP address of bitmain router is 192.168.1.1 – but sometimes, when you’re not able to login to this IP address of bitmain router, you can try login to 192.168.1.1 these IP addresses. There are few chances that these alternate IP addresses will work for you.
So now, we had known the IP address of bitmain router, but how can we login to my router’s default admin console? And do I need any username and password to login to my router’s console?
Logging to your router is very simple, which we discuss below – but if you want to login to your router, yes, you need to have default credentials of your bitmain router.
Sometimes the router may only take the default password and let you access their console for the very first time. And once you logged in to the console, you can set up your own username and password of the bitmain router.
To configure your router, you need to be logged in. Follow the step-by-step instructions and know-how to login to router and access the bitmain Interface.
If you want to reset the bitmain router, you need to remember that by performing a hard reset, the bitmain Router will be restored to Factory Default Settings. So, you should load the last configuration file or opt for configuration from the beginning.
Find the WPS/ RESET button on the rear of the device or located on the front panel.
You can find the Default address Domain name at the bottom label of the device.
The default login and Username are admin (You need to enter all the letters in lowercase)
Learn how to set up a bitmain extender. The process of the bitmain Wi-Fi Extender setup is straightforward.
The bitmain is a wireless Dual Gigabit Router that integrates a 4-port switch, Nat-Router, Firewall, and Wireless AP. If you want to know about the bitmain manual, then you need to know that there are several methods with which you can connect wireless devices to the extender. You can use the WPS or PIN Code to connect them. You can connect different wireless-enabled devices such as Android phones, tablets, and as well as Network Cards.
Below you can find the bitmain Wi-Fi Range Extender Manual: Follow the step-by-step instructions for bitmain setup.
With a router, you can easily connect multiple PCs and smartphones to the same network. Read on to know the step-by-step instructions for the same and learn how to reset bitmain Setup.
To connect the bitmain Router to a computer, you can use both the wired and wireless connection. For wired connection, plug one end of an Ethernet cable to the LAN port of the router and another to the LAN port of your computer. However, for wireless connection, look for the router’s SSID on your computer and connect to it by providing the wireless network passphrase.
If you forget the login password of your bitmain Router, you need to reset the router. Press and hold the reset button of the router for about 10 seconds. You will notice that the status lights are flickering and that the router reboots. This will restore the router’s settings as well as the default password.
If your bitmain Wireless Router setup is complete and you want to connect an iPad to it, follow the instructions listed below:
D-Link recommends a limit of up to 15 devices that can be connected to the router; however, this can be exceeded. The higher the number of connected devices, the more you will encounter issues with the internet speed.
If you can’t connect to bitmain Router, it means that the router cannot establish a connection. Follow these steps to resolve the issue:
The setup of bitmain Wireless Router requires a few important details such as the default IP address, username, and the password of the router. Once you log into the router admin panel, you can access the various tabs to configure your router and access the internet. Once the setup is complete, you can connect various wireless-enabled devices such as laptop, Android phone, iPad, iPhone, etc. to the router and access the internet.